lseek - reposition read/write file offset
off_t lseek(int fd, off_t offset, int whence);
The lseek() function repositions the offset of the open file associated with the file descriptor fd to the argument offset according to the directive whence as follows:
The lseek() function allows the file offset to be set beyond the end of the file (but this does not change the size of the file). If data is later written at this point, subsequent reads of the data in the gap (a "hole") return null bytes ( \0 ) until data is actually written into the gap.
SEEK_SET The offset is set to offset bytes. SEEK_CUR The offset is set to its current location plus offset bytes. SEEK_END The offset is set to the size of the file plus offset bytes.
Since version 3.1, Linux supports the following additional values for whence:
In both of the above cases, lseek() fails if offset points past the end of the file.
SEEK_DATA Adjust the file offset to the next location in the file greater than or equal to offset containing data. If offset points to data, then the file offset is set to offset. SEEK_HOLE Adjust the file offset to the next hole in the file greater than or equal to offset. If offset points into the middle of a hole, then the file offset is set to offset. If there is no hole past offset, then the file offset is adjusted to the end of the file (i.e., there is an implicit hole at the end of any file).
These operations allow applications to map holes in a sparsely allocated file. This can be useful for applications such as file backup tools, which can save space when creating backups and preserve holes, if they have a mechanism for discovering holes.
For the purposes of these operations, a hole is a sequence of zeros that (normally) has not been allocated in the underlying file storage. However, a file system is not obliged to report holes, so these operations are not a guaranteed mechanism for mapping the storage space actually allocated to a file. (Furthermore, a sequence of zeros that actually has been written to the underlying storage may not be reported as a hole.) In the simplest implementation, a file system can support the operations by making SEEK_HOLE always return the offset of the end of the file, and making SEEK_DATA always return offset (i.e., even if the location referred to by offset is a hole, it can be considered to consist of data that is a sequence of zeros).
Upon successful completion, lseek() returns the resulting offset location as measured in bytes from the beginning of the file. On error, the value (off_t) -1 is returned and errno is set to indicate the error.
EBADF fd is not an open file descriptor. EINVAL whence is not valid. Or: the resulting file offset would be negative, or beyond the end of a seekable device. EOVERFLOW The resulting file offset cannot be represented in an off_t. ESPIPE fd is associated with a pipe, socket, or FIFO. ENXIO whence is SEEK_DATA or SEEK_HOLE, and the current file offset is beyond the end of the file.
SVr4, 4.3BSD, POSIX.1-2001.
SEEK_DATA and SEEK_HOLE are nonstandard extensions also present in Solaris, FreeBSD, and DragonFly BSD; they are proposed for inclusion in the next POSIX revision (Issue 8).
Some devices are incapable of seeking and POSIX does not specify which devices must support lseek().
On Linux, using lseek() on a tty device returns ESPIPE.
When converting old code, substitute values for whence with the following macros:
old new 0 SEEK_SET 1 SEEK_CUR 2 SEEK_END L_SET SEEK_SET L_INCR SEEK_CUR L_XTND SEEK_END
Note that file descriptors created by dup(2) or fork(2) share the current file position pointer, so seeking on such files may be subject to race conditions.
dup(2), fork(2), open(2), fseek(3), lseek64(3), posix_fallocate(3)
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.