delete_module - unload a kernel module
int delete_module(const char *name, int flags);
Note: There is no glibc wrapper for this system call; see NOTES.
The delete_module() system call attempts to remove the unused loadable module entry identified by name. If the module has an exit function, then that function is executed before unloading the module. The flags argument is used to modify the behavior of the system call, as described below. This system call requires privilege.
Module removal is attempted according to the following rules:
The O_TRUNC flag has one further effect on the rules described above. By default, attempting to remove a module that has an init function but no exit function fails. However, if O_TRUNC was specified, this requirement is bypassed.
1. If there are other loaded modules that depend on (i.e., refer to symbols defined in) this module, then the call fails. 2. Otherwise, if the reference count for the module (i.e., the number of processes currently using the module) is zero, then the module is immediately unloaded. 3. If a module has a nonzero reference count, then the behavior depends on the bits set in flags. In normal usage (see NOTES), the O_NONBLOCK flag is always specified, and the O_TRUNC flag may additionally be specified.
The various combinations for flags have the following effect:
flags == O_NONBLOCK The call returns immediately, with an error. flags == (O_NONBLOCK | O_TRUNC) The module is unloaded immediately, regardless of whether it has a nonzero reference count. (flags & O_NONBLOCK) == 0 If flags does not specify O_NONBLOCK, the following steps occur:
* The module is marked so that no new references are permitted. * If the modules reference count is nonzero, the caller is placed in an uninterruptible sleep state (TASK_UNINTERRUPTIBLE) until the reference count is zero, at which point the call unblocks. * The module is unloaded in the usual way.
Using the O_TRUNC flag is dangerous! If the kernel was not built with CONFIG_MODULE_FORCE_UNLOAD, this flag is silently ignored. (Normally , CONFIG_MODULE_FORCE_UNLOAD is enabled.) Using this flag taints the kernel (TAINT_FORCED_RMMOD).
On success, zero is returned. On error, -1 is returned and errno is set appropriately.
EBUSY The module is not "live" (i.e., it is still being initialized or is already marked for removal); or, the module has an init function but has no exit function, and O_TRUNC was not specified in flags.
EFAULT name refers to a location outside the processs accessible address space. ENOENT No module by that name exists. EPERM The caller was not privileged (did not have the CAP_SYS_MODULE capability), or module unloading is disabled (see /proc/sys/kernel/modules_disabled in proc(5)). EWOULDBLOCK Other modules depend on this module; or, O_NONBLOCK was specified in flags, but the reference count of this module is nonzero and O_TRUNC was not specified in flags.
delete_module() is Linux-specific.
Glibc does not provide a wrapper for this system call; call it using syscall(2).
The uninterruptible sleep that may occur if O_NONBLOCK is omitted from flags is considered undesirable, because the sleeping process is left in an unkillable state. As at Linux 3.7, specifying O_NONBLOCK is optional, but in future kernels it is likely to become mandatory.
In Linux 2.4 and earlier, the system call took only one argument:
int delete_module(const char *name);
If name is NULL, all unused modules marked auto-clean are removed.
Some further details of differences in the behavior of delete_module() in Linux 2.4 and earlier are not currently explained in this manual page.
create_module(2), init_module(2), query_module(2), lsmod(8), modprobe(8), rmmod(8)
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/.